![]() Find the correct sized plate and press out the old ball jointĪnd then press in the new ball joint. Which looks like a giant c clamp and comes with many different pressing plates. If you choose to press out the ball joint you will need a ball joint pressing tool If you choose to replace the entire armīe sure to check out the control arm section on this webpage. You will need to either press out the old ball joint or replace the entire control arm as an assembly. The most common oneįor replacement is the lower ball joint which on this vehicle is attached to the lower control arm. The Dodge Ram 3500 has two sets of front ball joints being the upper and lower ball joints. From here we can reinstall the wheelĪnd torque down the lugnuts to 150 ft-lbs.ĭodge Ram 3500 Front Axle Nut Torque Spec : 280 ft-lbsĭodge Ram 3500 Front Wheel Bearing Bolts Torque Spec : 150 ft-lbs If an AWD model be sure to hand tighen down the 4 wheel hub bolts and torque them down to 150 ft-lbs.īe sure to use a large enough torque wrench for this as that is a rather large amount of force. Start by hand tightening it down and then torque the nut Wheel hub can be installed by putting it in the place of the old one and reinstalling the nut. If not you simply just remove the 4 bolts which hold the wheel bearing onto the steering knuckle and the wheel hub will be removable. With the nut removed the front wheel hub can be removed from the vehicle with ease by simply pulling it away from the steering knuckle if a RWD model. ![]() From here simply remove the center nut either by using a breaker bar or an impact gun. With the braking system removed we can now gainīetter access to the front wheel hub and its single center nut. To the braking system and remove the caliper so that the rotor can then be taken off of the vehicle. To start off we will want to jack up the vehicle and remove the tire on the side you wish to replace. Regardless of whichever version you have the steps will be relatively the same with the exception of working around the center cv axle. However, the actual wheel bearing assembly gets tightened down to the steering knuckle using 3 main bolts. Located in the center of the steering knuckle which allows for the front cv axle to come through and attach to the wheel hub using a similar single nut. On rear wheel drive models theįront wheel bearing gets tightened down to the steering knuckle using a single center nut. The front wheel hub on the Dodge Ram 3500 is different depending on whether the vehicle is 4WD or RWD. When putting the tie rod onto the vehicle the tie rod end nuts get tightened down to 65 ft-lbs.īe sure to install new cotter pins to ensure that vehicle safety is maintained.ĭodge Ram 3500 Outer Tie Rod End Torque Spec : 65 ft-lbsĭodge Ram 3500 Inner Tie Rod Torque Spec : 65 ft-lbs Whenever steering components are changed I recommend having an alignment done after the job to ensure the vehicle is in goodįunctional condition. This inner tie rod screws into the power steering rack and can be torqued down to 65 ft-lbs.īe sure to inspect and measure your old tie rods so that the new ones can be installedĬorrectly. The outer tie rod itself connects with another inner portion of the rod through the use If any of the steering rods are looseīe sure to replace them appropiately. Tie rod is apart of an entire rod system which controls the steering of the vehicle. Once the tire is off you can now access the old tie rod and remove it for replacement. Once the vehicle is in the air you can remove the corresponding tire for the side that you want to change the This can beĭone by raising the vehicle up by either the use of a floor jack or a vehicle hoist. To install a new tie rod on a Dodge Ram 3500 you must first remove the old one from the vehicle.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |